Открытый доступ Открытый доступ  Ограниченный доступ Доступ для подписчиков

Контроль крупных выделений нитрида титана в высокопрочной низколегированной стали

Лю Тао, Чен Дэн Фу, Лун Муцзюнь, Лю Пэн, Дуань Хуамэй, Гуй Линьтао, Фань Хэлинь, Чэнь Хуабяо

Аннотация


Исследовано влияние добавок титана и азота в высокопрочную низколегированную сталь 0,16 % С - 1 % Mn, а также скорости охлаждения при кристаллизации на выделения нитрида титана TiN и комплексных частиц TiN - CaS. Проанализированы процессы формирования и роста частиц TiN и TiN × CaS в твердо-жидкой зоне с использованием термодинамической модели диффузионного роста. Проведена экспериментальная проверка термодинамических расчетов. Осуществлен контроль стали на наличие крупных включений TiN.

Ключевые слова


включения TiN; комплексные включения TiN - CaS; термодинамика выделения; кинетика роста; контроль выделений; TiN inclusions; complex TiN - CaS inclusions; precipitation thermodynamics; growth kinetics; control of precipitates

Полный текст:

PDF

Литература


Ghosh P., Ghosh C., Ray R. K. Thermodynamics of precipitation and textural development in batch-annealed interstitial- free high-strength steels // Acta Materialia. 2010. V. 58(11). P. 3842 - 3850.

Chen J. Influence of deformation temperature on γ-α phase transformation in Nb - Ti microalloyed steel during continuous cooling // ISIJ International, 2013. V. 53(6). P. 1070 - 1075.

Elfaramawy H. S., Ghali S. N., Eissa M. M. Effect of titanium addition on behavior of medium carbon steel // Journal of Minerals & Materials Characterization & Engineering. 2013. V. 11(11). P. 1108 - 1112.

Cizek P., Wynne B. P., Davies C. H. J. et al. Effect of composition and austenite deformation on the transformation characteristics of low-carbon and ultralow-carbon microalloyed steels // Metallurgical & Materials Transactions A. 2002. V. 33(5). P. 1331 - 1349.

Gomez M., Rancel L., Gomez P. P., Robla J. I., Medina S. F. Simplification of hot rolling schedule in Ti-microalloyed steels with optimised Ti/N ratio // ISIJ International. 2010. V. 50(6). P. 868 - 874.

Zhang Y., Li X., Ma H. Enhancement of heat-affected zone toughness of a low carbon steel by TiN particle // Metallurgical & Materials Transactions. B. 2016. V. 47(4). P. 2148 - 2156.

Jiangxin Lu. Research and Development of a High Strength Micro-alloyed Steel With Yield Strength of 700 MPa: Diss. Northeastern University, 2005.

Yan W., Shan Y. Y., Yang K. Influence of TiN inclusions on the cleavage fracture behavior of low-carbon microalloyed steels // Metallurgical & Materials Transactions A. 2007. V. 38(6). P. 1211 - 1222.

Zhang L. P., Davis C. L., Strangwood M. Dependency of fracture toughness on the inhomogeneity of coarse TiN particle distribution in a low alloy steel // Metallurgical & Materials Transactions A. 2001. V. 32(5). P. 1147 - 1155.

Strangwood C. L., Davis C. L. Effect of TiN particles and grain size on the charpy impact transition temperature in steels // Journal of Materials Science & Technology. 2012. V. 28(10). P. 878 - 888.

Ghosh A., Ray A., Chakrabarti D., Davis C. L. Cleavage initiation in steel: Competition between large grains and large particles // Materials Science & Engineering A. 2013. V. 561(3). P. 126 - 135.

Wen-jun, Yan-ping, Li-hua, Zhao Wang. Control of the precipitation of TiN inclusions in gear steels // International Journal of Minerals, Metallurgy and Materials, 2014. V. 21(3). P. 234 - 239.

Ma F., Wen G., Tang P. Y. et al. In situ observation and investigation of effect of cooling rate on slab surface microstructure evolution in microalloyed steel // Ironmaking & Steelmaking. 2010. V. 37(3). P. 211 - 218.

Dou K., Meng L., Liu Q. et al. Influence of cooling rate on secondary phase precipitation and proeutectoid phase transformation of micro-alloyed steel containing vanadium // Metals and Materials International. 2016. V. 22(3). P. 349.

Zhao S., Wu Y-J., He M-F., Zhang L. Effects of cooling rates on microstructures and mechanical properties of Nb - Ti microalloyed steel // Journal of Shanghai Jiaotong University (Science). 2012. V. 17(6). P. 653 - 657.

Ma F., Wen G., Tang P., Xu G. et al. Effect of cooling rate on the precipitation behavior of carbonitride in microalloyed steel slab // Metallurgical & Materials Transactions B. 2011. V. 42(1). P. 81 - 86.

Ghosh A., Ray A., Chakrabarti D., Davis C. L. Cleavage initiation in steel: Competition between large grains and large particles // Materials Science & Engineering A. Structural Materials Properties Microstructure & Processing. 2013. V. 561(3). P. 126 - 135.

Yan W., Shan Y. Y., Yang K. Effect of TiN inclusions on the impact toughness of low-carbon microalloyed steels // Metallurgical and Materials Transactions A. 2006. V. 37(7). P. 2147 - 2158.

Yan W., Shan Y. Y., Yang K. Influence of TiN inclusions on the cleavage fracture behavior of low-carbon microalloyed steels // Metallurgical and Materials Transactions A. 2007. V. 38(6). P. 1211 - 1222.

Zhang L. P., Davis C. L., Strangwood M. Dependency of fracture toughness on the inhomogeneity of coarse TiN particle distribution in a low alloy steel // Metallurgical and Materials Transactions A. 2001. V. 32(5). P. 1147 - 1155.

Linaza M. A., Romero J. L., Rodriguez-Ibabe J. M., Urcola J. J. Influence of the microstructure on the fracture toughness and fracture mechanisms of forging steels microalloyed with titanium with ferrite-pearlite structures // Scripta Metallurgica et Materialia. 1993. V. 29.4(4), P. 451 - 456.

Linaza M. A., Romero J. L., Rodriguez-Ibabe J. M. Urcola J. J. Cleavage fracture of microalloyed forging steels // Scripta Metallurgica et Materialia. 1995. V. 32(3). P. 395 - 400.

Zhang L. P., Davis C. L., Strangwood M. Effect of TiN particles and microstructure on fracture toughness in simulated heat-affected zones of a structural steel // Metallurgical and Materials Transactions A. 1999. V. 30(8). P. 2089 - 2096.

Wan X. L., Wu K. M., Huang G., Wei R., Cheng L. In situ observation of austenite grain growth behavior in the simulated coarse-grained heat-affected zone of Ti-microalloyed steels // International Journal of Minerals. Metallurgy and Materials. 2014. V. 21(9). P. 878 - 885.

Zhang L. P., Davis C. L., Strangwood M. Effect of TiN particles and microstructure on fracture toughness in simulated heat-affected zones of a structural steel // Metallurgical & Materials Transactions A. 1999. V. 30(8). 2089 - 2096.

Zarandi F., Yue S. Mechanism for loss of hot ductility due to deformation during solidification in continuous casting of steel // ISIJ International. 2007. V. 44(10). P. 1705 - 1713.

Jung J. G., Park J. S., Kim J., Lee Y. K. Carbide precipitation kinetics in austenite of a Nb - Ti - V microalloyed steel // Materials Science & Engineering A. 2011. V. 528(16 - 17). P. 5529 - 5535.

Liu H. Y., Wang H. L., Li L. et al. Investigation of Ti inclusions in wire cord steel // Ironmaking & Steelmaking. 2011. V. 38(1). P. 53 - 58.

Wen-jun Ma, Yan-ping Bao, Li-hua Zhao, Min Wang. Control of theprecipitation of TiN inc lusionsingearsteels // International Journal of Minerals. Metallurgy and Materials. 2014. V. 21(3). P. 234 - 239.

Maehara Y., Yasumoto K., Tomono H. et al. Surface cracking mechanism of continuously cast low carbon low alloy steel slabs // Materials Science and Technology. 1990. V. 6(9). P. 793 - 806.

Jong-Jin P., Jong-Oh J. O., Sun-In K. et al. Thermodynamics of titanium and oxygen dissolved in liquid iron equilibrated with titanium oxides // ISIJ International. 2007. V. 47(1). P. 16 - 24.

Sigworth G. K., Elliott J. F. The Thermodynamics of liquid dilute iron alloys // Metal Science. 1974. V. 8(1). P. 298 - 310.

Wang Y. N., Bao Y. P., Wang M., Zhang L. C. Precipitation and control of BN inclusions in 42CrMo steel and their effect on machinability // International Journal of Minerals, Metallurgy and Materials. 2013. V. 20(9). P. 842 - 849.

Kawashita Y., Suito H. Precipitation behavior of Al - Ti - O - N inclusions in unidirectionally solidified Fe - 30 mass% Ni alloy // ISIJ International. 1995. V. 35(12). 1468 - 1476.

Xu G., Jiang Z., Li Y. Formation mechanism of cas-bearing inclusions and the rolling deformation in Al-killed, low-alloy steel with Ca treatment // Metallurgical & Materials Transactions B. 2016. V. 47(4). P. 2411 - 2420.

Ohnaka I. Mathematical analysis of solute redistribution during solidification with diffusion in solid phase // Transactions of the Iron & Steel Institute of Japan. 1986. V. 26(12). P. 1045 - 1051.

El-Bealy M., Thomas B. G. Prediction of dendrite arm spacing for low alloy steel casting processes // Metallurgical and Materials Transactions B. 1996. V. 27(4). P. 689 - 693.

Clyne T. W., Kurz W. Solute redistribution during solidification with rapid solid state diffusion // Metallurgical and Materials Transactions A. 1981. V. 12(6). P. 965 - 971.

Liu Y., Zhang L., Duan H. et al. Extraction, Thermodynamic analysis, and precipitation mechanism of MnS - TiN complex inclusions in low-sulfur steels // Metallurgical and Materials Transactions A. 2016. V. 47(6). P. 3015 - 3025.

Choudhary S. K., Ghosh A. Mathematical model for prediction of composition of inclusions formed during solidification of liquid steel // ISIJ International. 2009. V. 49(12). P. 1819 - 1827.

Goto H., Ken-Ichi M., Yamada W., Tanaka K. Effect of cooling rate on composition of oxides precipitated during solidification of steels // ISIJ International. 1995. V. 35(6). P. 708 - 714.

Liu W. J., Yue S., Jonas J. J. Characterization of Ti carbosulfide precipitation in Ti microalloyed steels // Metallurgical and Materials Transactions A. 1989. V. 20(10). P. 1907 - 191.




DOI: https://doi.org/10.30906/mitom.2019.9.9-17

© Издательский дом «Фолиум», 1998–2025