Открытый доступ Открытый доступ  Ограниченный доступ Платный доступ или доступ для подписчиков

Анализ структуры и свойств трубного соединения из жаропрочного сплава HP40NbTi, полученного в режиме импульсной GTAW-сварки

С. Ю. Кондратьев, М. Д. Фукс

Аннотация


Методами световой и электронной микроскопии, рентгеноспектрального микроанализа исследованы микроструктура и фазовый состав трубного сварного соединения из сплава HP40NbTi на основе системы Fe – 25Cr – 35Ni, выполненного в режиме импульсной GTAW-сварки. Определены его кратковременные и длительные механические свойства. Установлено, что более равномерное температурное поле с пониженным уровнем температур, возникающее при импульсной сварке, по сравнению с полем при стандартной сварке, предотвращает активное развитие фазового превращения NbC ® G в сплаве HP40NbTi. Это способствует формированию более однородной структуры металла шва, большей равнопрочности различных зон сварного соединения и повышению его эксплуатационных свойств.


Ключевые слова


жаропрочные аустенитные сплавы; сварное соединение; импульсный режим сварки GTAW; микроструктура; фазовый состав; G-фаза; механические свойства

Полный текст:

PDF

Литература


Garbiak M., Jasinski W., Piekarski B. Materials for reformer furnace tubes. History of evolution // Arch. Foundry Eng. 2011. V. 11, Is. 2. P. 47 – 52.

Tawancy H. M., Ul-Hamid A., Mohammed A. I., Abbas N. M. Effect of materials selection and design on the performance of an engineering product — An example from petrochemical industry // Mater. Des. 2007. V. 28, Is. 2. P. 686 – 703.

Tillack D. J., Guthrie J. E. Wrought and Cast Heat-Resistant Stainless Steels and Nickel Alloys for the Refining and Petrochemical Industries / Nickel Development Institute, Toronto, Technical Series, 1998. No. 10. P. 71 – 85.

Hu B., Chen X., Liu C. et al. Study on microstructure and properties of centrifugal casting 35Cr45NiNb + MA furnace tubes during service // Mater. High Temp. 2019. V. 36, Is. 6. P. 489 – 498.

Borjali S., Allahkaram S. R., Khosravi H. Effects of working temperature and carbon diffusion on the microstructure of high pressure heat-resistant stainless steel tubes used in pyrolysis furnaces during service condition // Mater. Des. 2012. V. 34. P. 65 – 73.

Kondrat’ev S. Y., Anastasiadi G. P., Ptashnik A. V., Petrov S. N. Kinetics of the high-temperature oxidation of heat-resistant statically and centrifugally cast HP40NbTi alloys // Oxid. Met. 2019. V. 91, Is. 1 – 2. P. 33 – 53.

Kondrat’ev S. Yu., Anastasiadi G. P., Petrov S. N., Ptashnik A. V. Kinetics of the formation of intermetallic phases in HP-type heat-resistant alloys at long-term high-temperature exposure // Metall. Mater. Trans. A. 2017. V. 48, Is. 1. P. 482 – 492.

Kondrat’ev S. Yu., Anastasiadi G. P., Ptashnik A. V., Petrov S. N. The mechanisms of scale and subsurface diffusion zone formation of heat-resistant HP40NbTi alloy at long-term high-temperature exposure // Materialia. 2019. V. 7. Art. 100427.

Kenik E. A., Maziasz P. J., Swindeman R. W. et al. Structure and phase stability in cast modified-HP austenite after long-term ageing // Scr. Mater. 2003. V. 49, Is. 2. P. 117 – 122.

Santos M., Guedes M., Baptista R. et al. Effect of severe operation conditions on the degradation state of radiant coins in pyrolysis furnaces // Eng. Failure Anal. 2015. V. 56. P. 194 – 203.

De Almeida L. H., Ribeiro A. F., Le May I. Microstructural characterization of modified 25Cr – 35Ni centrifugally cast steel furnace tubes // Mater. Charact. 2003. V. 49, Is. 3. P. 219 – 229.

Rudskoy A. I., Oryshchenko A. S., Kondrat’ev S. Yu. et al. Mechanisms and kinetics of phase transformations in refractory alloy 45Kh26N33S2B2 in long-term high-temperature holds. Part 1 // Met. Sci. Heat Treat. 2014. V. 56, Is. 1 – 2. P. 3 – 8.

Rudskoy A. I., Kondrat’ev S. Yu., Anastasiadi G. P. et al. Mechanism and kinetics of phase transformations in refractory alloy 45Kh26N33S2B2 under long-term high-temperature holds. Part 2 // Met. Sci. Heat Treat. 2014. V. 56, Is. 3 – 4. P. 124 – 130.

Guo J., Cao T., Cheng C. et al. Microstructure evolution and mechanical properties degradation of HPNb alloy after a five-year service // Mater. Res. Express. 2018. V. 5, Is. 4. Art. 046509.

Monobe L. S., Schхn C. G. Microstructural and fractographic investigation of a centrifugally cast 20Cr32Ni + Nb alloy tube in the ‘as cast’ and aged states // J. Mater. Res. Technol. 2013. V. 2, Is. 2. P. 195 – 201.

Ilman M. N., Kusmono. Analysis of material degradation and life assessment of 25Cr – 38Ni – Mo – Ti wrought alloy steel (HPM) for cracking tubes in an ethylene plant // Eng. Failure Anal. 2014. V. 42. P. 100 – 108.

Anwar Ul-Hamid, Hani M. Tawancy, Abdul-Rashid I. Mohammed, Nureddin M. Abbas. Failure analysis of furnace radiant tubes exposed to excessive temperature // Eng. Failure Anal. 2006. V. 13. P. 1005 – 1021.

Bonaccorsi L., Guglielmino E., Pino E. et al. Damage analysis in Fe – Cr – Ni centrifugally cast alloy tubes for reforming furnaces // Eng. Failure Anal. 2014. V. 36. P. 65 – 74.

Antonello Alvino, Daniela Lega, Francesco Giacobbe et al. Damage characterization in two reformer heater tubes after nearly 10 years of service at different operative and maintenance conditions // Eng. Failure Anal. 2010. V. 17, Is. 7 – 8. P. 1526 – 1541.

Ghatak A., Robi P. S. High-temperature tensile properties and creep life assessment of 25Cr35NiNb micro-alloyed steel // J. Mater. Eng. Perform. 2016. V. 25, Is. 5. P. 2000 – 2007.

Singhatham C., Eidhed K. The study of welding repair parameters of tube 35Cr – 45Ni – Nb alloy of the ethylene heating furnace // Appl. Mech. Mater. 2016. No. 848. P. 35 – 38.

Reihani A., Haghighi R. D. Failure analysis and weld ability improvement of 35 % Cr – 45 % Ni heat resistant alloy // Eng. Failure Anal. 2015. V. 52. P. 97 – 108.

Abbasi M., Park I., Ro Y. et al. Microstructural evaluation of welded fresh-to-aged reformer tubes used in hydrogen production plants // Eng. Failure Anal. 2018. V. 92. P. 368 – 377.

Mostafaei M., Shamanian M., Purmohamad H., Amini M. Increasing weldability of service-aged reformer tubes by partial solution annealing // J. Mater. Eng. Perform. 2016. V. 25. P. 1291 – 1303.

Allahkaram S. R., Borjali S., Khosravi H. Investigation of weldability and property changes of high pressure heat-resistant cast stainless steel tubes used in pyrolysis furnaces after a five-year service // Mater. Des. 2012. V. 33. P. 476 – 484.

Guglielmino E., Pino R., Servetto C., Sili A. Damage investigation on welded tubes of a reforming furnace // La Metallurgia Italiana. 2015. V. 107, Is. 1. P. 53 – 58.

Shinozaki K., Kuroki H., Nakao Y. et al. Deterioration of weldability of long-term aged HP heat-resistant cast steel containing Nb, Mo, and W // Weld. Int. 1999. V. 13, Is. 1. P. 39 – 48.

Guan K., Wang Q. Analysis of failed electron beam welds in ethylene cracking tubes // Eng. Failure Anal. 2011. V. 18, Is. 5. P. 1366 – 1374.

Reihani A., Razavi S. A., Abbasi E. et al. Failure analysis of welded radiant tubes made of cast heat-resisting steel // J. Fail. Anal. Prevent. 2013. V. 13, Is. 6. P. 658 – 665.

Guo J., Liu W., Li C., Zhang