Открытый доступ Открытый доступ  Ограниченный доступ Платный доступ или доступ для подписчиков

Влияние криогенной обработки на свойства высокомолибденовой легированной стали

Hediye AYDIN

Аннотация


Исследовано влияние глубокой криогенной обработки на микроструктуру и механические свойства инструментальной стали SLD Magic (Cr8Mo2) и проанализирована взаимосвязь между микроструктурой и свойствами. После высокотемпературного отжига и аустенитизации проводили криогенную обработку стали Cr8Mo2 при –145 и –196 °C в течение различного времени выдержки: 12, 24, 36 и 48 ч. После криогенной обработки образцы стали каждой группы с разным временем выдержки подвергали отпуску при 200 и 520 °C в течение 1 ч. Изучена микроструктура и фазовый состав, измерена микротвердость. Выполнены испытания на абразивный износ и ударную вязкость стали в различных состояниях.

Ключевые слова


сталь SLD Magic (Cr8Mo2); криогенная обработка; микроструктура; механические свойства; абразивный износ

Полный текст:

PDF

Литература


N. Magazov, Z. Satbaeva, B. Rakhadilov, A. Amanov, A study on surface hardening and wear resistance of AISI 52100 steel by ultrasonic nanocrystal surface modification and electrolytic plasma surface modification technologies, Mater. 16 (20) (2023) 6824.

https://doi.org/10.3390/ma16206824

V.K. Parikh, A.D. Badgujar, M.R.N.M. Qureshi, Effect of cryogenic treatment on non-ferrous materials: A review, Int. J. Mater. Eng. Innov. (ahead of print) (2024).

https://doi.org/10.1504/IJMATEI.2024.138603

J. Mraz, T. Bakalova, The impact of cryogenic temperatures on the hardness and tribological properties of cobalt alloys, Manuf. Technol. 24 (4) (2024) 626–635.

https://doi.org/10.21062/mft.2024.057

R.W. Thornton, Investigating the effects of cryogenic processing on the wear performance and microstructure of engineering materials, Ph.D. Thesis, University of Sheffield, 2014.

V. Karakurt, F. Öztürk, T. Çıtrak, G.N. Gözüak, O. Zığındere, Effect of deep cryogenic treatment on microstructural and mechanical properties of high-performance CPOH and WP7V tool steels, Int. J. Mater. Eng. Technol. 7 (2) (2024) 77–84.

https://doi.org/10.70858/tijmet.1499365

S. Chowwanonthapunya, W. Tiranatsakul, W. Wongkokua, Cryogenic treatment of tool steels: A brief review and a case report, Marit. Technol. Res. 4 (2) (2022) 211–218.

https://doi.org/10.33175/mtr.2022.253445

S. Li, Y. Xie, X. Wu, Hardness and toughness investigations of deep cryogenic treated cold work die steel, Cryogenics 50 (2) (2010) 89–92.

https://doi.org/10.1016/j.cryogenics.2009.12.005

T. Sonar, S. Lomte, C. Gogte, Cryogenic treatment of metal – a review, Mater. Today: Proc. 5 (11) (2018) 25219–25228.

https://doi.org/10.1016/j.matpr.2018.10.324

P. Jovičević-Klug, B. Podgornik, Review on the effect of deep cryogenic treatment of metallic materials in automotive applications, Metals 10 (4) (2020) 434.

https://doi.org/10.3390/met10040434

C.R. Anoop, R.K. Singh, R.R. Kumar, M. Jayalakshmi, T.A. Prabhu, K.T. Tharian, S.V.S.N. Murty, A review on steels for cryogenic applications, Mater. Perform. Charact. 10 (2) (2021) 16–88.

https://doi.org/10.1520/MPC20200193

V. Yarasu, P. Jurci, J. Ptacinova, I. Dlouhy, J. Hornik, Effect of cryogenic treatments on hardness, fracture toughness, and wear properties of Vanadis 6 tool steel, Mater. 17 (7) (2024) 1688.

https://doi.org/10.3390/ma17071688

M.A. Essam, A.Y. Shash, M.K. El-Fawakhry, E. El-Kashif, H. Megahed, Effect of deep cryogenic treatment on wear behavior of cold work tool steel, Metals 13 (2023) 382.

https://doi.org/10.3390/met13020382

B. Li, C. Li, Y. Wang, X. Jin, Effect of cryogenic treatment on microstructure and wear resistance of carburized 20CrNi2MoV steel, Metals 8 (2018) 808.

https://doi.org/10.3390/met8100808

S.J. Gobbi, V.J. Gobbi, G. Reinke, P.V. Muterlle, D.M. Rosa, Ultra-low-temperature process effects on microscale abrasion of tool steel AISI D2, Mater. Sci. Technol. 35 (11) (2019) 1355–1364.

https://doi.org/10.1080/02670836.2019.16240

H. Aydin, Improving the mechanical and wear performance of AISI D2 steel with a cryogenic treatment, Afyon Kocatepe Univ. J. Sci. Eng. 25 (2) (2025) 423–432.

https://doi.org/10.35414/akufemubid.1497089

D. Das, K.K. Ray, A.K. Dutta, Influence of varied cryogenic treatments on the wear behavior of AISI D2 steel, Wear 266 (1–2) (2009) 297–309.

https://doi.org/10.1016/j.wear.2008.07.001

J. Bi, L. Li, J. Peng, J. Liao, Y. Gao, Effect of deep cryogenic treatment on microstructure and properties of M35 high speed steel, J. Phys.: Conf. Ser. 2044 (1) (2021) 012014.

1088/1742-6596/2044/1/012014

B. Li, S. Zhang, T. Zhang, J. Zhang, Effect of deep cryogenic treatment on microstructure, mechanical properties and machining performances of coated carbide tool, J. Braz. Soc. Mech. Sci. Eng. 41 (1) (2019) 27.

https://doi.org/10.1007/s40430-018-1533-6

T. Balaško, M. Vončina, J. Burja, J. Medved, Influence of heat treatment on the high-temperature oxidation behaviour of chromium-molybdenum-vanadium alloyed hot-work tool steel, Mater. Technol. 56 (2) (2022) 233–241.

https://doi.org/10.17222/mit.2022.406

D.N. Collins, J. Dormer, Deep cryogenic treatment of tool steels, Heat Treat. Met. 3 (1997) 71–74.

P. Baldissera, C. Delprete, Effects of deep cryogenic treatment on static mechanical properties of 18NiCrMo5 carburized steel, Mater. Des. 29 (8) (2008) 1735–1740.

https://doi.org/10.1016/j.matdes.2008.08.015

D. Senthilkumar, I. Rajendran, M. Pellizzari, Effect of cryogenic treatment on the hardness and tensile behaviour of AISI 4140 steel, Int. J. Microstruct. Mater. Prop. 6 (5) (2011) 366–377.

https://doi.org/10.1504/IJMMP.2011.043573

A. Akhbarizadeh, S. Javadpour, Investigating the effect of holding duration on the microstructure of 1.2080 tool steel during the deep cryogenic heat treatment, Vacuum. 86(10) (2012) 1534-1540. https://doi.org/10.1016/j.vacuum.2012.02.013

V. Leskovšek, M. Kalin, J. Vižintin, Influence of deep-cryogenic treatment on wear resistance of vacuum heat-treated HSS, Vacuum 80 (6) (2006) 507–518.

https://doi.org/10.1016/j.vacuum.2005.08.023

D. Toboła, W. Brostow, K. Czechowski, P. Rusek, Improvement of wear resistance of some cold working tool steels, Wear 382 (2017) 29–39.

https://doi.org/10.1016/j.wear.2017.03.023

K.K. Ray, D. Das, Improved wear resistance of steels by cryotreatment: The current state of understanding, Mater. Sci. Technol. 33 (3) (2017) 340–354.

https://doi.org/10.1080/02670836.2016.1206292

K. Du, Z. Lv, W. Fan, R. Zhang, X. Li, L. Xu, Effect of heat treatment process on microstructure and mechanical properties of high-carbon H13 steel, Processes 11 (11) (2023) 3239.

https://doi.org/10.3390/pr11113239




DOI: https://doi.org/10.30906/mitom.2026.5.20-20


© Издательский дом «Фолиум», 1998–2026