Открытый доступ Открытый доступ  Ограниченный доступ Доступ для подписчиков

Исследование микроструктуры и твердости медных композитов, армированных Co - Ti

Эмине Сап, Махыр Узун

Аннотация


Исследованы микроструктура и твердость композитов с медной матрицей и армирующими добавками 5, 10 и 15 % (масс.) Co - Ti, полученными смешиванием частиц армирующего порошка и порошка Cu высокой чистоты, прессованием и спеканием при 1000 °C. Определена плотность композиционных материалов. Установлены условия получения наиболее плотного композита с высокой твердостью.

Ключевые слова


микроструктура; твердость; порошковая металлургия; кобальт; титан

Полный текст:

PDF

Литература


Bobrynina E. V., Larionova T. V., Kol'tsova T. S. et al. Preparation, structure and properties of copper-based composites with additions of fullerenes and fullerene soot // Met. Sci. Heat Treat. 2020. V. 62, Is. 1. P. 70 - 75.

Abd-Elwahed M. S., Meselhy A. F. Experimental investigation on the mechanical, structural and thermal properties of Cu - ZrO2 nanocomposites hybridized by graphene nanoplatelets // Ceram. Int. 2020. V. 46, Is. 7. P. 9198 - 9206.

Цzgьn Ц., Bulut C. A novel mixing method for powder metallurgy copper-carbon nanotube composites // Materwiss. Werksttech. 2020. Bd. 51, No. 7. S. 982 - 991.

Prosviryakov A. SiC content effect on the properties of Cu - SiC composites produced by mechanical alloying // J. Alloys Compd. 2015. V. 632. P. 707 - 710.

Kirik I., Ozdemir N., Caligulu U. Effect of particle size and volume fraction of the reinforcement on the microstructure and mechanical properties of friction welded MMC to AA6061 aluminum alloy // Kovove Mater. 2013. V. 51, Is. 4. P. 221 - 227.

Akbarpour M., Salahi E., Hesari F. A. et al. Microstructural development and mechanical properties of nanostructured copper reinforced with SiC nanoparticles // Mater. Sci. Eng. A. 2013. V. 568. P. 33 - 39.

Islak S., Зalıgьlь U., Hraam H. R. H. et al. Electrical conductivity, microstructure and wear properties of Cu - Mo coatings // Res. Eng. Struct. Mat. 2019. V. 5, Is. 2. P. 137 - 146.

Cao H., Qian Z., Zhang L. et al. Tribological behavior of Cu matrix composites containing graphite and tungsten disulfide // Tribol. Trans. 2014. V. 57, Is. 6. P. 1037 - 1043.

Chen X., Bao R., Yi J. et al. Enhancing mechanical properties of pure copper-based materials with CrxOy nanoparticles and CNT hybrid reinforcement // J. Mater. Sci. 2021. V. 56, Is. 4. P. 3062 - 3077.

Naghikhani M., Ardestani M., Moazami-Goudarzi M. Microstructure, mechanical properties and wear performance of WC/brass composites produced by pressureless and spark plasma sintering processes // Met. Mater. Int. 2019. V. 25, Is. 4. P. 1 - 10.

Xiao J. K., Zhang W., Liu L. M., Zhang L., Zhang C. Tribological behavior of copper-molybdenum disulfide composites // Wear. 2017. V. 384. P. 61 - 71.

Gua Sh., Zheng H., Shu X. et al. Synthesis and properties of reduced graphene oxide-copper composites produced by the method of repeated pressing and sintering // Met. Sci. Heat Treat. 2019. V. 61, Is. 5. P. 387 - 393.

Abd El Aal M. I. Effect of high-pressure torsion processing on the microstructure evolution and mechanical properties of consolidated micro size Cu and Cu - SiC powders // Adv. Powder Technol. 2017. V. 28, Is. 9. P. 2135 - 2150.

Venkatesh R., Rao V. S. Thermal, corrosion and wear analysis of copper based metal matrix composites reinforced with alumina and graphite // Def. Technol. 2018. V. 14, Is. 4. P. 346 - 355.

Uzun M., Munis M. M., Usca Ь. A. Different ratios CrC particle-reinforced Cu matrix composite materials and investigation of wear performance // Int. J. Eng. Res. Appl. 2018. V. 8, Is. 7. P. 1 - 7.

Sap E. Microstructural and mechanical properties of Cu-based Co - Mo-reinforced composites produced by the powder metallurgy method // J. Mater. Eng. Perform. 2020. V. 29, Is. 12. P. 8461 - 8472.

Fatoba O. S., Adesina O. S., Popoola A. P. I. Evaluation of microstructure, microhardness, and electrochemical properties of laser-deposited Ti - Co coatings on Ti - 6Al - 4V Alloy // Int. J. Adv. Manuf. Tech. 2018. V. 97, Is. 5. P. 2341 - 2350.

Hao H., Mo W., Lv Y. et al. The effect of trace amount of Ti and W on the powder metallurgy process of Cu // J. Alloys Compd. 2016. V. 660. P. 204 - 207.

Chundru V. R., Koona R., Pujari S. R. Surface modification of Ti6Al4V alloy using EDMed electrode made with nano-and micron-sized TiC/Cu powder particles // Arab. J. Sci. Eng. 2019. V. 44, Is. 2. P. 1425 - 1436.

Karakulak E. Characterization of Cu - Ti powder metallurgical materials // Int. J. Miner. Metall. Mater. 2017. V. 24, Is. 1. P. 83 - 90.

Deng Z., Yin H., Zhang C., Li W. Microstructure and mechanical properties of Cu - 12Al - 6Ni with Ti addition prepared by powder metallurgy // Mater. Sci. Eng. A. 2020. 140472.

Uzun M., Usca U. A. Effect of Cr particulate reinforcements in different ratios on wear performance and mechanical properties of Cu matrix composites // J. Braz. Soc. Mech. Sci. & Eng. 2018. V. 40, Is. 4. 197.

Sadeghi N., Aghajani H., Akbarpour M. R. Microstructure and tribological properties of in-situ TiC - C/Cu nanocomposites synthesized using different carbon sources (graphite, carbon nanotube and graphene) in the Cu - Ti - C system // Ceram. Int. 2018. V. 44, Is. 18. P. 22059 - 22067.




DOI: https://doi.org/10.30906/mitom.2021.10.40-45

© Издательский дом «Фолиум», 1998–2024